Posts Tagged ‘digital’
ANCEL AC3000 digital manifold is a professisional instrument for installation, testing and maintenance of refrigeration equipment suchas air conditioners and cold stores. It combines 2-way pressure test, dual temperature measurements (with optionaldual temperature probes), a 32-bit digitalprocessor and a large LCD in one easy-to-useinstrument with the following main functions. Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-timeSuperheat and Subcooling Simultaneously Display with Optional Two Clamp-onTemperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /? Conversion. It is the right one you have to do the job right. Turn off the blue valve and red valve. Turn on the instrument. Then verify that LCD displays the status of the pressure test. If not, press the function button to switch it. When the instrument is turned on, theremay be 10 digits in the high and low pressure display area. Press R+/ R- buttons, Unit button and? /? Button to select tested refrigerant and reading display respectively. If the clamp-on temperature probes havebeen connected to the instrument, the real-time temperature will be displayed. If not, no display of it. Connect the instrument to the refrigeration system according to thechart below. Turn on the refrigerant valve and gently press the pressure release valve to vent the air in the connecting hose. When the refrigeration system stops, turnon the high pressure valve (red valve) and fill with a certain amount of refrigerant and then shut the valve quickly. Run the refrigeration system, turn on the low pressure valve (blue valve), and fill with the refrigerant into the refrigeration system. After the filling is completed, shut the low pressure valve (blue valve) and refrigerant valve. Let the refrigeration system running. Shut down the refrigeration system, make sure all valves are turned off, then disconnect the instrument between refrigeration system and source. Do not remove the high pressure valve connection until the pressure drops to the safe point. Then turn off the instrument. The filling operation of different equipment or refrigerants may vary. Please read carefully the relevant specific operation requirements for filling operation, so as to avoid damage to user or equipment caused by improper operation! The instrument can display the corresponding Evaporation Temperature(EV) and Condensation Temperature (CO) during the refrigerant pressure test. If the clamp-on temperature probes are connected to the instrument, LCD will display the real-time temperature in the spot T1 Sensor and T2 Sensor. Please make sure clamp-on temperature probes are connected as step 6 and contacted fully to the refrigeration pipes. The instrument can calculate the SH-Superheat and SC – Subcooling as long as the tested refrigerant ispreset and clamp-on temperature probes are connected well. Power on the instrument. Then make surethe LCD displays vacuum test status. If not, press the Function button to switch it. When the instrument is turned on, there may be 10 digits in the high and low pressure display area. Press the unit button to adjust the reading unit. Connect the instrument to the refrigeration system. Connected clamp-on temperature probes will not affect the operation. Turn on the blue valve and red valve, andstart the vacuum pump. After the vacuum operation is completed, turn off the blue valve and red valve, then shut the vacuum pump. At this time, pressure leak test mode can be used to check leakage in the system (Please refer to Pressure Leak Test). The instrument is powered on with the blue and red valves turned off. Press the Function button to pressure leak test mode. The current pressure value is displayed at lower rightcorner of LCD. Press the Run/Stop button to start the leak test. At this time, the lower left corner records the initial pressure value; the lower right corner displays the instantaneous pressure value; the “P” display area shows the difference between the initial pressure value and the instantaneous pressure value. The time display shows how long the leak test will take, in hour : minute (HH:MM)format. All pressure units on the screen are the same. You can switch between the different pressure units by pressing the Unit button. 89 Kids of Refrigeant Database. Built-in 89 kinds of refrigerant NIST: According to AmericanNIST standard. R11 R113 R114 R115 R116 R12 R123 R124 R125 R1270. R13 R134A R14 R141B R142B R143A R152A R170 R21 R218. R22 R227EA R23 R236EA R245CA R245FA R290 R32 R401A R401B. R401C R402A R402B R403A R403B R404A R405A R406A R407A R407B. R407C R407D R407E R408A R409A R409B R41 R410A R410B R411A. R411B R412A R413A R414A R414B R415A R415B R416A R417A R418A. R419A R420A R421A R421B R422A R422B R422C R422D R423A R424A. R425A R426A R427A R428A R50 R500 R501 R502 R503 R504. R507A R508A R507B R509A R600 R600A R707 R7441C02 R1234. Wide Range of applications. Pressure test: gauge pressure. Pressure test unit: Kpa; Mpa; bar; inHg; PSI. Pressure test range: 0 Kpa – 6000 Kpa. Pressure test resolution: 1 Kpa. Pressure test accuracy: +/- 0.5 %(FS)+ 5dgt. Pressure overload limit: 10000 Kpa (10 Mpa; 100 bar;). Vacuum test: relative vacuum. Vacuum test unit: Kpa; Mpa; bar; inHg; PSI. Vacuum test range: -101 Kpa – 0 Kpa. Vacuum test resolution: 1 Kpa. Temperature test unit: °C (Celsius), °F (Fahrenheit). Temperature test range: -40°C-150°C (-40°F-302°F). 0.1°C (-40°C-99.9°C), 1°C (100°C-150°C). 0.1°F (-40°F-99.9°F), 1°F (100°F-302°F). Temperature test accuracy: +/- 0.5 °C + 2dgt +/- 0.9 °F + 2dgt. Power Supplies: 4 X 1.5V SIZE. AA / LR6 Battery not include. Ancel AC3000 refrgerantion Digital Manifold Gauge. Clamp on temperature probe socket. 5, R+/R-Refrigerant Type Selection Buttons. 10, High Pressure Button. 11, Refrigerant Obezervation Window. 12, Pressure release valve. 13, Refrigerant inlet/vacuum Pump inlet. 14, Low Pressure Valve. 15,1/4 inch high pressure inlet. 1 x AC3000 Manifold Digital Meter. 1 x Paper Box. 1 x User Manual. Clean the exterior with a damp cloth. Do not use harsh solvents. Keep screw connections clean and free of grease, clean with a moist cloth as required. Carefully blow out oil residues in valve block using compressed air. Replace the batteries when low battery power indication lights on in LCD. Low battery power supply. The instruments has low power sign. When it is displayed, it means the battery power is insufficient. At this time, the battery should be replaced as required in order to avoid affecting normal use. Damaged refrigerant hose orvalve stem. Please check the pipe connections and hoses before testing. If you find any damage, please replace them immediately to avoid improper use or accident. Failure of refrigerant filling. There is a valve core in the refrigerant inlet of the refrigeration system. When connecting the instrument, pay attention the two terminals of the hoses. Connect one terminal with a core to the refrigeration system, while another terminal without acore to the instrument. Every hose terminal comes with a nylonpad that is limited a certain life of using. Over use or other situation will make itdefective, which result in leakage. The instrument refrigerant inlet (the middle port of the instrument) has a port with valve core, which is used to vent the air in the hoes after connecting the refrigerant to the instrument. The port is equipped with a copper plug screw. It is required to tighten it every time before or after operation. Check the refrigeration system’s pipes and connectors. Credit cards? Debit card? Apple Pay? Google Pay ect. Carrier and Logistics: All Orders are. Free repair for the devices. OBDII Code Reader, Car Diagnostic Tool, Truck Diagnostic Tool, EVAP Smoke Machine, Car Power Probe, Battery Tester. The price is reasonable and we have top rated after-sales service. Our main brand is. And we also sell other brands product, such as. FOXWELL, LAUNCH, THINKCAR, AUTOPHIX. GMT8 (9:00-18:00). From Monday to Friday.
Battery Chargers & Boosters. Alternator Auxilary Drive Belt. Air Con Conditioning Top up Aircon Refill Regas DIY R-134a Gas X2 Digital Gauge. Did you know that your Air Conditioning system in your car can loose around 10% of its gas refrigerant a year? Regular maintaince using the A/C Pro Air Conditioning recharge will restore your Air Conditioning system back to its original specification. Restores lost refrigerant and oil to A/C system. Formulated with advanced QwikBoost chemistry that was developed for NASA. Colder air up to 50% faster. Eliminates moisture and acid from A/C system. Contains leak sealer for common leaks in rubber hoses, gaskets and o-rings. Will tune up, lubricate, clean and recharge R-134a automotive A/C systems. Designed to work with A/C Pro Auto Freeze Air Conditioning Digital dispenser and gauge (included in this package). 24 long heavy duty hose not the short hosed version that cant always reach!!! Guided Commands eliminates the guesswork. Easy to use for DIY users. Reusable and can be used as an A/C check gauge without attaching to container. Calibrated and colour coded gauge for easy use. THE A/C PRO AIR CONDINTIONING RECHARGE ONLY WORKS WITH THE ORIGINAL R-134A GAS!! We pride ourselves on giving fantastic customer service and competitive prices on quality items! Please note if you do not wish for the item to be left in a safe place or with a neighbour this must be added to the notes at the checkout process. When returning goods back to us please make sure all outer packaging is in a re-saleable condition. We stress that all buyers leave their vehicle registration number to check fitment, failure to do so will mean we pressume that you have checked all the data accurately and correctly. View more great items. Car Air Con Bomb Top Up Kit charge Refill A/C With Gauge Super Seal STP. STP Auto Freeze R-134A Air Conditioning Reusable Trigger Dispenser & Gauge A/C. AIR CON SEALER STOP LEAK & WITH LEAK DETECTOR SEALS STP SUPER SEAL AIRCON FIX. CAR VAN AIR CON CONDITIONING RECHARGE TOP UP REFILL GAS DIY AF-1/6. Sign up to Newsletter. This listing is currently undergoing maintenance, we apologise for any inconvenience caused.
89 Refrigeration Digital Manifold Gauge HVAC Vacuum Temp. What is the Ancel AC3000? Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-time Display with Optional Two Clamp-on Temperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /°F Conversion. It is the right one you have to do the job right. Ancel AC3000 Evaporation/Condesing Pressureand Temperaturetest. Ancel AC3000 Pressure Leakage Test. Calculate the pressure difference between the initial test pressure and the second test pressure to determine if the refrigerant is leaking. The temperature of the refrigerant in the high/low pressurepipelines of the air condidtioning system. Wide Range of applications. Automotive Air Conditioning Household Air Conditioning Cold Storage Refrigeration Equipment. Ancel AC3000 built 89 Kids of refrigeant database. Refrigerant Type Can Be Set Filled With Refrigerant Through The Visual Window. It can be set according to the type of refrigerant that the car needs to fil the refrigerant filling status can be observed through a viewable window. Refrgerant Digital Manifold Gauge. Ancel AC3000 refrgerantion Digital Manifold Gauge. Clamp on temperature probe socket 1, Lcd display 2, Function Button 3, Run/Stop Button 4, Zero button 5, R+/R-Refrigerant Type Selection Buttons 6, Backlit button 7, Unit Button 8, C/F Button 9, Power button 10, High Pressure Button 11, Refrigerant Obezervation Window 12, Pressure release valve 13, Refrigerant inlet/vacuum Pump inlet 14, Low Pressure Valve 15,1/4 inch high pressure inlet. Open the battery compartment by squeezing the clip lock 2. We accept Credit cards? Debit card? Apple Pay? Google Pay ect. Electronic VAT receipt available upon request. If you accidentally placed the wrong order, please. To cancel the order. All our products are 100% original and brand new with latest version. All Orders are. Please do not open a case!! We really appreciate your understanding! My company is authorize distributor, officially authorized by brands owner and headquarter. 3 Year free repair for the devices. Some high level tools do require to be registered to get authorization before use. If the item has been used, we have the right to decline your claim. We are professional dealer specialized in vehicle car. From entry level basic Code Reader. To Professional OBD2 Scanner. ALL System Car Diagnostic Service Tool. Immobilizer Key Match Tool, Car Locksmith Tool. And other automotive electronics. We are in the industry for more than 10 years. We are authorized primary distributor of many leading companies in the industry, including. Launch, Foxwell, Thinkcar, Autek, ANCEL, Innova, Autophix, Kzyee. And more brands will be available in our store in near future. What Do We Provide? High quality original products. Safer, up-to-date software, and updates. Free online tech support. We provide remote online assistance via TeamViewer, if you have any difficulty in software installation. Our corporation is established for the purpose of trustworthiness. Your satisfaction is our priority, we assure you not only get quality products but also good service. If youhave any problem about the goods, please. We promise to help you solve it asap, and make you feel satisfactory absolutely. 2: our business time. Customer Service: Monday-Friday: 2:00AM – 12:00PM GMT(London Standard Time). We will do the same as soon as we can too. 4:If you like the item. It is our biggest honor. If you write a 5-stars????? Product Review in the listing, it will help many other car owers for sure.
89 Refrigeration Digital Manifold Gauge HVAC Vacuum Temp. What is the Ancel AC3000? Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-time Display with Optional Two Clamp-on Temperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /°F Conversion. It is the right one you have to do the job right. Ancel AC3000 Evaporation/Condesing Pressureand Temperaturetest. Ancel AC3000 Pressure Leakage Test. Calculate the pressure difference between the initial test pressure and the second test pressure to determine if the refrigerant is leaking. The temperature of the refrigerant in the high/low pressurepipelines of the air condidtioning system. Wide Range of applications. Automotive Air Conditioning Household Air Conditioning Cold Storage Refrigeration Equipment. Ancel AC3000 built 89 Kids of refrigeant database. Refrigerant Type Can Be Set Filled With Refrigerant Through The Visual Window. It can be set according to the type of refrigerant that the car needs to fil the refrigerant filling status can be observed through a viewable window. Refrgerant Digital Manifold Gauge. Ancel AC3000 refrgerantion Digital Manifold Gauge. Clamp on temperature probe socket 1, Lcd display 2, Function Button 3, Run/Stop Button 4, Zero button 5, R+/R-Refrigerant Type Selection Buttons 6, Backlit button 7, Unit Button 8, C/F Button 9, Power button 10, High Pressure Button 11, Refrigerant Obezervation Window 12, Pressure release valve 13, Refrigerant inlet/vacuum Pump inlet 14, Low Pressure Valve 15,1/4 inch high pressure inlet. Open the battery compartment by squeezing the clip lock 2. We accept Credit cards? Debit card? Apple Pay? Google Pay ect. Electronic VAT receipt available upon request. If you accidentally placed the wrong order, please. To cancel the order. All our products are 100% original and brand new with latest version. All Orders are. Please do not open a case!! We really appreciate your understanding! My company is authorize distributor, officially authorized by brands owner and headquarter. 3 Year free repair for the devices. Some high level tools do require to be registered to get authorization before use. If the item has been used, we have the right to decline your claim. We are professional dealer specialized in vehicle car. From entry level basic Code Reader. To Professional OBD2 Scanner. ALL System Car Diagnostic Service Tool. Immobilizer Key Match Tool, Car Locksmith Tool. And other automotive electronics. We are in the industry for more than 10 years. We are authorized primary distributor of many leading companies in the industry, including. Launch, Foxwell, Thinkcar, Autek, ANCEL, Innova, Autophix, Kzyee. And more brands will be available in our store in near future. What Do We Provide? High quality original products. Safer, up-to-date software, and updates. Free online tech support. We provide remote online assistance via TeamViewer, if you have any difficulty in software installation. Our corporation is established for the purpose of trustworthiness. Your satisfaction is our priority, we assure you not only get quality products but also good service. If youhave any problem about the goods, please. We promise to help you solve it asap, and make you feel satisfactory absolutely. 2: our business time. Customer Service: Monday-Friday: 2:00AM – 12:00PM GMT(London Standard Time). We will do the same as soon as we can too. 4:If you like the item. It is our biggest honor. If you write a 5-stars????? Product Review in the listing, it will help many other car owers for sure.
ANCEL AC3000 digital manifold is a professisional instrument for installation, testing and maintenance of refrigeration equipment suchas air conditioners and cold stores. It combines 2-way pressure test, dual temperature measurements (with optionaldual temperature probes), a 32-bit digitalprocessor and a large LCD in one easy-to-useinstrument with the following main functions. Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-timeSuperheat and Subcooling Simultaneously Display with Optional Two Clamp-onTemperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /? Conversion. It is the right one you have to do the job right. Turn off the blue valve and red valve. Turn on the instrument. Then verify that LCD displays the status of the pressure test. If not, press the function button to switch it. When the instrument is turned on, theremay be 10 digits in the high and low pressure display area. Press R+/ R- buttons, Unit button and? /? Button to select tested refrigerant and reading display respectively. If the clamp-on temperature probes havebeen connected to the instrument, the real-time temperature will be displayed. If not, no display of it. Connect the instrument to the refrigeration system according to thechart below. Turn on the refrigerant valve and gently press the pressure release valve to vent the air in the connecting hose. When the refrigeration system stops, turnon the high pressure valve (red valve) and fill with a certain amount of refrigerant and then shut the valve quickly. Run the refrigeration system, turn on the low pressure valve (blue valve), and fill with the refrigerant into the refrigeration system. After the filling is completed, shut the low pressure valve (blue valve) and refrigerant valve. Let the refrigeration system running. Shut down the refrigeration system, make sure all valves are turned off, then disconnect the instrument between refrigeration system and source. Do not remove the high pressure valve connection until the pressure drops to the safe point. Then turn off the instrument. The filling operation of different equipment or refrigerants may vary. Please read carefully the relevant specific operation requirements for filling operation, so as to avoid damage to user or equipment caused by improper operation! The instrument can display the corresponding Evaporation Temperature(EV) and Condensation Temperature (CO) during the refrigerant pressure test. If the clamp-on temperature probes are connected to the instrument, LCD will display the real-time temperature in the spot T1 Sensor and T2 Sensor. Please make sure clamp-on temperature probes are connected as step 6 and contacted fully to the refrigeration pipes. The instrument can calculate the SH-Superheat and SC – Subcooling as long as the tested refrigerant ispreset and clamp-on temperature probes are connected well. Power on the instrument. Then make surethe LCD displays vacuum test status. If not, press the Function button to switch it. When the instrument is turned on, there may be 10 digits in the high and low pressure display area. Press the unit button to adjust the reading unit. Connect the instrument to the refrigeration system. Connected clamp-on temperature probes will not affect the operation. Turn on the blue valve and red valve, andstart the vacuum pump. After the vacuum operation is completed, turn off the blue valve and red valve, then shut the vacuum pump. At this time, pressure leak test mode can be used to check leakage in the system (Please refer to Pressure Leak Test). The instrument is powered on with the blue and red valves turned off. Press the Function button to pressure leak test mode. The current pressure value is displayed at lower rightcorner of LCD. Press the Run/Stop button to start the leak test. At this time, the lower left corner records the initial pressure value; the lower right corner displays the instantaneous pressure value; the “P” display area shows the difference between the initial pressure value and the instantaneous pressure value. The time display shows how long the leak test will take, in hour : minute (HH:MM)format. All pressure units on the screen are the same. You can switch between the different pressure units by pressing the Unit button. 89 Kids of Refrigeant Database. Built-in 89 kinds of refrigerant NIST: According to AmericanNIST standard. R11 R113 R114 R115 R116 R12 R123 R124 R125 R1270. R13 R134A R14 R141B R142B R143A R152A R170 R21 R218. R22 R227EA R23 R236EA R245CA R245FA R290 R32 R401A R401B. R401C R402A R402B R403A R403B R404A R405A R406A R407A R407B. R407C R407D R407E R408A R409A R409B R41 R410A R410B R411A. R411B R412A R413A R414A R414B R415A R415B R416A R417A R418A. R419A R420A R421A R421B R422A R422B R422C R422D R423A R424A. R425A R426A R427A R428A R50 R500 R501 R502 R503 R504. R507A R508A R507B R509A R600 R600A R707 R7441C02 R1234. Wide Range of applications. Pressure test: gauge pressure. Pressure test unit: Kpa; Mpa; bar; inHg; PSI. Pressure test range: 0 Kpa – 6000 Kpa. Pressure test resolution: 1 Kpa. Pressure test accuracy: +/- 0.5 %(FS)+ 5dgt. Pressure overload limit: 10000 Kpa (10 Mpa; 100 bar;). Vacuum test: relative vacuum. Vacuum test unit: Kpa; Mpa; bar; inHg; PSI. Vacuum test range: -101 Kpa – 0 Kpa. Vacuum test resolution: 1 Kpa. Temperature test unit: °C (Celsius), °F (Fahrenheit). Temperature test range: -40°C-150°C (-40°F-302°F). 0.1°C (-40°C-99.9°C), 1°C (100°C-150°C). 0.1°F (-40°F-99.9°F), 1°F (100°F-302°F). Temperature test accuracy: +/- 0.5 °C + 2dgt +/- 0.9 °F + 2dgt. Power Supplies: 4 X 1.5V SIZE. AA / LR6 Battery not include. Ancel AC3000 refrgerantion Digital Manifold Gauge. Clamp on temperature probe socket. 5, R+/R-Refrigerant Type Selection Buttons. 10, High Pressure Button. 11, Refrigerant Obezervation Window. 12, Pressure release valve. 13, Refrigerant inlet/vacuum Pump inlet. 14, Low Pressure Valve. 15,1/4 inch high pressure inlet. 1 x AC3000 Manifold Digital Meter. 1 x Paper Box. 1 x User Manual. Clean the exterior with a damp cloth. Do not use harsh solvents. Keep screw connections clean and free of grease, clean with a moist cloth as required. Carefully blow out oil residues in valve block using compressed air. Replace the batteries when low battery power indication lights on in LCD. Low battery power supply. The instruments has low power sign. When it is displayed, it means the battery power is insufficient. At this time, the battery should be replaced as required in order to avoid affecting normal use. Damaged refrigerant hose orvalve stem. Please check the pipe connections and hoses before testing. If you find any damage, please replace them immediately to avoid improper use or accident. Failure of refrigerant filling. There is a valve core in the refrigerant inlet of the refrigeration system. When connecting the instrument, pay attention the two terminals of the hoses. Connect one terminal with a core to the refrigeration system, while another terminal without acore to the instrument. Every hose terminal comes with a nylonpad that is limited a certain life of using. Over use or other situation will make itdefective, which result in leakage. The instrument refrigerant inlet (the middle port of the instrument) has a port with valve core, which is used to vent the air in the hoes after connecting the refrigerant to the instrument. The port is equipped with a copper plug screw. It is required to tighten it every time before or after operation. Check the refrigeration system’s pipes and connectors. About Invoices: If an. Much appreciated to leave us your. ANCEL specializes in automotive intelligent diagnostics, detection and analysis systems, and automotive-related products for mechanics, repair shops, and DIYers. Our independent brand is. FOXWELL, LAUNCH, AUTOPHIX, OBDPROG ect. If there are any after-sales or pre-sales messages that can be sent to us, we will promptly handle them and provide satisfactory solutions. Model, make year, VIN. And tell me the main problem of your car, we will check and recommend a suitable product for you. Any questions, Please feel free to.
ANCEL AC3000 digital manifold is a professisional instrument for installation, testing and maintenance of refrigeration equipment suchas air conditioners and cold stores. It combines 2-way pressure test, dual temperature measurements (with optionaldual temperature probes), a 32-bit digitalprocessor and a large LCD in one easy-to-useinstrument with the following main functions. Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-timeSuperheat and Subcooling Simultaneously Display with Optional Two Clamp-onTemperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /? Conversion. It is the right one you have to do the job right. Turn off the blue valve and red valve. Turn on the instrument. Then verify that LCD displays the status of the pressure test. If not, press the function button to switch it. When the instrument is turned on, theremay be 10 digits in the high and low pressure display area. Press R+/ R- buttons, Unit button and? /? Button to select tested refrigerant and reading display respectively. If the clamp-on temperature probes havebeen connected to the instrument, the real-time temperature will be displayed. If not, no display of it. Connect the instrument to the refrigeration system according to thechart below. Turn on the refrigerant valve and gently press the pressure release valve to vent the air in the connecting hose. When the refrigeration system stops, turnon the high pressure valve (red valve) and fill with a certain amount of refrigerant and then shut the valve quickly. Run the refrigeration system, turn on the low pressure valve (blue valve), and fill with the refrigerant into the refrigeration system. After the filling is completed, shut the low pressure valve (blue valve) and refrigerant valve. Let the refrigeration system running. Shut down the refrigeration system, make sure all valves are turned off, then disconnect the instrument between refrigeration system and source. Do not remove the high pressure valve connection until the pressure drops to the safe point. Then turn off the instrument. The filling operation of different equipment or refrigerants may vary. Please read carefully the relevant specific operation requirements for filling operation, so as to avoid damage to user or equipment caused by improper operation! The instrument can display the corresponding Evaporation Temperature(EV) and Condensation Temperature (CO) during the refrigerant pressure test. If the clamp-on temperature probes are connected to the instrument, LCD will display the real-time temperature in the spot T1 Sensor and T2 Sensor. Please make sure clamp-on temperature probes are connected as step 6 and contacted fully to the refrigeration pipes. The instrument can calculate the SH-Superheat and SC – Subcooling as long as the tested refrigerant ispreset and clamp-on temperature probes are connected well. Power on the instrument. Then make surethe LCD displays vacuum test status. If not, press the Function button to switch it. When the instrument is turned on, there may be 10 digits in the high and low pressure display area. Press the unit button to adjust the reading unit. Connect the instrument to the refrigeration system. Connected clamp-on temperature probes will not affect the operation. Turn on the blue valve and red valve, andstart the vacuum pump. After the vacuum operation is completed, turn off the blue valve and red valve, then shut the vacuum pump. At this time, pressure leak test mode can be used to check leakage in the system (Please refer to Pressure Leak Test). The instrument is powered on with the blue and red valves turned off. Press the Function button to pressure leak test mode. The current pressure value is displayed at lower rightcorner of LCD. Press the Run/Stop button to start the leak test. At this time, the lower left corner records the initial pressure value; the lower right corner displays the instantaneous pressure value; the “P” display area shows the difference between the initial pressure value and the instantaneous pressure value. The time display shows how long the leak test will take, in hour : minute (HH:MM)format. All pressure units on the screen are the same. You can switch between the different pressure units by pressing the Unit button. 89 Kids of Refrigeant Database. Built-in 89 kinds of refrigerant NIST: According to AmericanNIST standard. R11 R113 R114 R115 R116 R12 R123 R124 R125 R1270. R13 R134A R14 R141B R142B R143A R152A R170 R21 R218. R22 R227EA R23 R236EA R245CA R245FA R290 R32 R401A R401B. R401C R402A R402B R403A R403B R404A R405A R406A R407A R407B. R407C R407D R407E R408A R409A R409B R41 R410A R410B R411A. R411B R412A R413A R414A R414B R415A R415B R416A R417A R418A. R419A R420A R421A R421B R422A R422B R422C R422D R423A R424A. R425A R426A R427A R428A R50 R500 R501 R502 R503 R504. R507A R508A R507B R509A R600 R600A R707 R7441C02 R1234. Wide Range of applications. Pressure test: gauge pressure. Pressure test unit: Kpa; Mpa; bar; inHg; PSI. Pressure test range: 0 Kpa – 6000 Kpa. Pressure test resolution: 1 Kpa. Pressure test accuracy: +/- 0.5 %(FS)+ 5dgt. Pressure overload limit: 10000 Kpa (10 Mpa; 100 bar;). Vacuum test: relative vacuum. Vacuum test unit: Kpa; Mpa; bar; inHg; PSI. Vacuum test range: -101 Kpa – 0 Kpa. Vacuum test resolution: 1 Kpa. Temperature test unit: °C (Celsius), °F (Fahrenheit). Temperature test range: -40°C-150°C (-40°F-302°F). 0.1°C (-40°C-99.9°C), 1°C (100°C-150°C). 0.1°F (-40°F-99.9°F), 1°F (100°F-302°F). Temperature test accuracy: +/- 0.5 °C + 2dgt +/- 0.9 °F + 2dgt. Power Supplies: 4 X 1.5V SIZE. AA / LR6 Battery not include. Ancel AC3000 refrgerantion Digital Manifold Gauge. Clamp on temperature probe socket. 5, R+/R-Refrigerant Type Selection Buttons. 10, High Pressure Button. 11, Refrigerant Obezervation Window. 12, Pressure release valve. 13, Refrigerant inlet/vacuum Pump inlet. 14, Low Pressure Valve. 15,1/4 inch high pressure inlet. 1 x AC3000 Manifold Digital Meter. 1 x Paper Box. 1 x User Manual. Clean the exterior with a damp cloth. Do not use harsh solvents. Keep screw connections clean and free of grease, clean with a moist cloth as required. Carefully blow out oil residues in valve block using compressed air. Replace the batteries when low battery power indication lights on in LCD. Low battery power supply. The instruments has low power sign. When it is displayed, it means the battery power is insufficient. At this time, the battery should be replaced as required in order to avoid affecting normal use. Damaged refrigerant hose orvalve stem. Please check the pipe connections and hoses before testing. If you find any damage, please replace them immediately to avoid improper use or accident. Failure of refrigerant filling. There is a valve core in the refrigerant inlet of the refrigeration system. When connecting the instrument, pay attention the two terminals of the hoses. Connect one terminal with a core to the refrigeration system, while another terminal without acore to the instrument. Every hose terminal comes with a nylonpad that is limited a certain life of using. Over use or other situation will make itdefective, which result in leakage. The instrument refrigerant inlet (the middle port of the instrument) has a port with valve core, which is used to vent the air in the hoes after connecting the refrigerant to the instrument. The port is equipped with a copper plug screw. It is required to tighten it every time before or after operation. Check the refrigeration system’s pipes and connectors. About Invoices: If an. Much appreciated to leave us your. ANCEL specializes in automotive intelligent diagnostics, detection and analysis systems, and automotive-related products for mechanics, repair shops, and DIYers. Our independent brand is. FOXWELL, LAUNCH, AUTOPHIX, OBDPROG ect. If there are any after-sales or pre-sales messages that can be sent to us, we will promptly handle them and provide satisfactory solutions. Model, make year, VIN. And tell me the main problem of your car, we will check and recommend a suitable product for you. Any questions, Please feel free to.
ANCEL AC3000 digital manifold is a professisional instrument for installation, testing and maintenance of refrigeration equipment suchas air conditioners and cold stores. It combines 2-way pressure test, dual temperature measurements (with optionaldual temperature probes), a 32-bit digitalprocessor and a large LCD in one easy-to-useinstrument with the following main functions. Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-timeSuperheat and Subcooling Simultaneously Display with Optional Two Clamp-onTemperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /? Conversion. It is the right one you have to do the job right. Turn off the blue valve and red valve. Turn on the instrument. Then verify that LCD displays the status of the pressure test. If not, press the function button to switch it. When the instrument is turned on, theremay be 10 digits in the high and low pressure display area. Press R+/ R- buttons, Unit button and? /? Button to select tested refrigerant and reading display respectively. If the clamp-on temperature probes havebeen connected to the instrument, the real-time temperature will be displayed. If not, no display of it. Connect the instrument to the refrigeration system according to thechart below. Turn on the refrigerant valve and gently press the pressure release valve to vent the air in the connecting hose. When the refrigeration system stops, turnon the high pressure valve (red valve) and fill with a certain amount of refrigerant and then shut the valve quickly. Run the refrigeration system, turn on the low pressure valve (blue valve), and fill with the refrigerant into the refrigeration system. After the filling is completed, shut the low pressure valve (blue valve) and refrigerant valve. Let the refrigeration system running. Shut down the refrigeration system, make sure all valves are turned off, then disconnect the instrument between refrigeration system and source. Do not remove the high pressure valve connection until the pressure drops to the safe point. Then turn off the instrument. The filling operation of different equipment or refrigerants may vary. Please read carefully the relevant specific operation requirements for filling operation, so as to avoid damage to user or equipment caused by improper operation! The instrument can display the corresponding Evaporation Temperature(EV) and Condensation Temperature (CO) during the refrigerant pressure test. If the clamp-on temperature probes are connected to the instrument, LCD will display the real-time temperature in the spot T1 Sensor and T2 Sensor. Please make sure clamp-on temperature probes are connected as step 6 and contacted fully to the refrigeration pipes. The instrument can calculate the SH-Superheat and SC – Subcooling as long as the tested refrigerant ispreset and clamp-on temperature probes are connected well. Power on the instrument. Then make surethe LCD displays vacuum test status. If not, press the Function button to switch it. When the instrument is turned on, there may be 10 digits in the high and low pressure display area. Press the unit button to adjust the reading unit. Connect the instrument to the refrigeration system. Connected clamp-on temperature probes will not affect the operation. Turn on the blue valve and red valve, andstart the vacuum pump. After the vacuum operation is completed, turn off the blue valve and red valve, then shut the vacuum pump. At this time, pressure leak test mode can be used to check leakage in the system (Please refer to Pressure Leak Test). The instrument is powered on with the blue and red valves turned off. Press the Function button to pressure leak test mode. The current pressure value is displayed at lower rightcorner of LCD. Press the Run/Stop button to start the leak test. At this time, the lower left corner records the initial pressure value; the lower right corner displays the instantaneous pressure value; the “P” display area shows the difference between the initial pressure value and the instantaneous pressure value. The time display shows how long the leak test will take, in hour : minute (HH:MM)format. All pressure units on the screen are the same. You can switch between the different pressure units by pressing the Unit button. 89 Kids of Refrigeant Database. Built-in 89 kinds of refrigerant NIST: According to AmericanNIST standard. R11 R113 R114 R115 R116 R12 R123 R124 R125 R1270. R13 R134A R14 R141B R142B R143A R152A R170 R21 R218. R22 R227EA R23 R236EA R245CA R245FA R290 R32 R401A R401B. R401C R402A R402B R403A R403B R404A R405A R406A R407A R407B. R407C R407D R407E R408A R409A R409B R41 R410A R410B R411A. R411B R412A R413A R414A R414B R415A R415B R416A R417A R418A. R419A R420A R421A R421B R422A R422B R422C R422D R423A R424A. R425A R426A R427A R428A R50 R500 R501 R502 R503 R504. R507A R508A R507B R509A R600 R600A R707 R7441C02 R1234. Wide Range of applications. Pressure test: gauge pressure. Pressure test unit: Kpa; Mpa; bar; inHg; PSI. Pressure test range: 0 Kpa – 6000 Kpa. Pressure test resolution: 1 Kpa. Pressure test accuracy: +/- 0.5 %(FS)+ 5dgt. Pressure overload limit: 10000 Kpa (10 Mpa; 100 bar;). Vacuum test: relative vacuum. Vacuum test unit: Kpa; Mpa; bar; inHg; PSI. Vacuum test range: -101 Kpa – 0 Kpa. Vacuum test resolution: 1 Kpa. Temperature test unit: °C (Celsius), °F (Fahrenheit). Temperature test range: -40°C-150°C (-40°F-302°F). 0.1°C (-40°C-99.9°C), 1°C (100°C-150°C). 0.1°F (-40°F-99.9°F), 1°F (100°F-302°F). Temperature test accuracy: +/- 0.5 °C + 2dgt +/- 0.9 °F + 2dgt. Power Supplies: 4 X 1.5V SIZE. AA / LR6 Battery not include. Ancel AC3000 refrgerantion Digital Manifold Gauge. Clamp on temperature probe socket. 5, R+/R-Refrigerant Type Selection Buttons. 10, High Pressure Button. 11, Refrigerant Obezervation Window. 12, Pressure release valve. 13, Refrigerant inlet/vacuum Pump inlet. 14, Low Pressure Valve. 15,1/4 inch high pressure inlet. 1 x AC3000 Manifold Digital Meter. 1 x Paper Box. 1 x User Manual. Clean the exterior with a damp cloth. Do not use harsh solvents. Keep screw connections clean and free of grease, clean with a moist cloth as required. Carefully blow out oil residues in valve block using compressed air. Replace the batteries when low battery power indication lights on in LCD. Low battery power supply. The instruments has low power sign. When it is displayed, it means the battery power is insufficient. At this time, the battery should be replaced as required in order to avoid affecting normal use. Damaged refrigerant hose orvalve stem. Please check the pipe connections and hoses before testing. If you find any damage, please replace them immediately to avoid improper use or accident. Failure of refrigerant filling. There is a valve core in the refrigerant inlet of the refrigeration system. When connecting the instrument, pay attention the two terminals of the hoses. Connect one terminal with a core to the refrigeration system, while another terminal without acore to the instrument. Every hose terminal comes with a nylonpad that is limited a certain life of using. Over use or other situation will make itdefective, which result in leakage. The instrument refrigerant inlet (the middle port of the instrument) has a port with valve core, which is used to vent the air in the hoes after connecting the refrigerant to the instrument. The port is equipped with a copper plug screw. It is required to tighten it every time before or after operation. Check the refrigeration system’s pipes and connectors. Greenwich Mean Time will be delivered on the same day! 12 months free repair for the devices. 3 months for the accessories. The price is reasonable and we have top rated after-sales service. Our agent brands are: ANCEL, FOXWELL, LAUNCH, THINKCAR, AUTOPHIX, etc. We promise to help you solve it asap, and make you feel satisfactory absolutely. After you received our package you are satisfied with it. We will do the same as soon as we can too.
The digital manifold gauge is an auxiliary instrument for the installation, testing and maintenance of refrigeration equipment such as air conditioners. The instrument has various functions such as dual pressure test, dual temperature test, digital readout, multi-unit switching and built-in refrigerant database. The digital manifold gauge adopts silicone anti-slip design on both sides to prevent slipping and comes with temperature clamps and refrigerant hoses. Design with V-shaped Valve Switch. The valve can be easily controlled, thus saving time from complicated knob operation. The amount of refilling refrigerant is easier to control than the refrigerant gauge using ordinary knob valves, which is convenient to operate and more durable. 3.5 inch Backlight LED Display. Large LCD digital display, each test result is divided by lines in the screen, making the data more intuitive and clear at a glance. Refrigant Subcooling and Superheating Temperature Test. The degree of supercooling/superheating is automatically read. The greater the degree of superheating, the less refrigerant is filling, the lower the degree of subcooling can improve the cooling capacity of the system. Temparature test range:-40-150? (-40-302F). A variety of units are designed for your needs. Pressure units:Kpa;Mpa;bar;inHg;PSI. Temperature units:? (Celsius), ? (Fahenheit). Condensing Pressure and Temperature Test. The minimum pressure when the refrigerant changes from gas to liquid, and the maximum temperature when the gas changes to liquid. Calculate the pressure difference between the initial test pressure and the second test pressure, and observe whether there is any leakage in the refrigeration system pipeline. Pressure test unit: Kpa; Mpa; bar; inHg; PSI. Pressure test range: 0 Kpa – 6000 Kpa. Pressure test resolution: 1 Kpa. Pressure test accuracy: +/- 0.5 %(FS)+ 5dgt. Pressure overload limit: 10000 Kpa (10 Mpa; 100 bar;). Vacuum test: relative vacuum. Vacuum test resolution: 1Kpa. International Buyers Please Note. We are a professional worldwide Professional company. We are reliable supplier to both wholesalers and retail sellers. We supply many products on Automobile consumer. Also offer reasonable prices, excellent customer service and a reliable credit standing are our target! All messages be reply within 24 hours. Welcome your any-time parchase!
ANCEL AC3000 digital manifold is a professisional instrument for installation, testing and maintenance of refrigeration equipment suchas air conditioners and cold stores. It combines 2-way pressure test, dual temperature measurements (with optionaldual temperature probes), a 32-bit digitalprocessor and a large LCD in one easy-to-useinstrument with the following main functions. Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-timeSuperheat and Subcooling Simultaneously Display with Optional Two Clamp-onTemperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /? Conversion. It is the right one you have to do the job right. Turn off the blue valve and red valve. Turn on the instrument. Then verify that LCD displays the status of the pressure test. If not, press the function button to switch it. When the instrument is turned on, theremay be 10 digits in the high and low pressure display area. Press R+/ R- buttons, Unit button and? /? Button to select tested refrigerant and reading display respectively. If the clamp-on temperature probes havebeen connected to the instrument, the real-time temperature will be displayed. If not, no display of it. Connect the instrument to the refrigeration system according to thechart below. Turn on the refrigerant valve and gently press the pressure release valve to vent the air in the connecting hose. When the refrigeration system stops, turnon the high pressure valve (red valve) and fill with a certain amount of refrigerant and then shut the valve quickly. Run the refrigeration system, turn on the low pressure valve (blue valve), and fill with the refrigerant into the refrigeration system. After the filling is completed, shut the low pressure valve (blue valve) and refrigerant valve. Let the refrigeration system running. Shut down the refrigeration system, make sure all valves are turned off, then disconnect the instrument between refrigeration system and source. Do not remove the high pressure valve connection until the pressure drops to the safe point. Then turn off the instrument. The filling operation of different equipment or refrigerants may vary. Please read carefully the relevant specific operation requirements for filling operation, so as to avoid damage to user or equipment caused by improper operation! The instrument can display the corresponding Evaporation Temperature(EV) and Condensation Temperature (CO) during the refrigerant pressure test. If the clamp-on temperature probes are connected to the instrument, LCD will display the real-time temperature in the spot T1 Sensor and T2 Sensor. Please make sure clamp-on temperature probes are connected as step 6 and contacted fully to the refrigeration pipes. The instrument can calculate the SH-Superheat and SC – Subcooling as long as the tested refrigerant ispreset and clamp-on temperature probes are connected well. Power on the instrument. Then make surethe LCD displays vacuum test status. If not, press the Function button to switch it. When the instrument is turned on, there may be 10 digits in the high and low pressure display area. Press the unit button to adjust the reading unit. Connect the instrument to the refrigeration system. Connected clamp-on temperature probes will not affect the operation. Turn on the blue valve and red valve, andstart the vacuum pump. After the vacuum operation is completed, turn off the blue valve and red valve, then shut the vacuum pump. At this time, pressure leak test mode can be used to check leakage in the system (Please refer to Pressure Leak Test). The instrument is powered on with the blue and red valves turned off. Press the Function button to pressure leak test mode. The current pressure value is displayed at lower rightcorner of LCD. Press the Run/Stop button to start the leak test. At this time, the lower left corner records the initial pressure value; the lower right corner displays the instantaneous pressure value; the “P” display area shows the difference between the initial pressure value and the instantaneous pressure value. The time display shows how long the leak test will take, in hour : minute (HH:MM)format. All pressure units on the screen are the same. You can switch between the different pressure units by pressing the Unit button. 89 Kids of Refrigeant Database. Built-in 89 kinds of refrigerant NIST: According to AmericanNIST standard. R11 R113 R114 R115 R116 R12 R123 R124 R125 R1270. R13 R134A R14 R141B R142B R143A R152A R170 R21 R218. R22 R227EA R23 R236EA R245CA R245FA R290 R32 R401A R401B. R401C R402A R402B R403A R403B R404A R405A R406A R407A R407B. R407C R407D R407E R408A R409A R409B R41 R410A R410B R411A. R411B R412A R413A R414A R414B R415A R415B R416A R417A R418A. R419A R420A R421A R421B R422A R422B R422C R422D R423A R424A. R425A R426A R427A R428A R50 R500 R501 R502 R503 R504. R507A R508A R507B R509A R600 R600A R707 R7441C02 R1234. Wide Range of applications. Pressure test: gauge pressure. Pressure test unit: Kpa; Mpa; bar; inHg; PSI. Pressure test range: 0 Kpa – 6000 Kpa. Pressure test resolution: 1 Kpa. Pressure test accuracy: +/- 0.5 %(FS)+ 5dgt. Pressure overload limit: 10000 Kpa (10 Mpa; 100 bar;). Vacuum test: relative vacuum. Vacuum test unit: Kpa; Mpa; bar; inHg; PSI. Vacuum test range: -101 Kpa – 0 Kpa. Vacuum test resolution: 1 Kpa. Temperature test unit: °C (Celsius), °F (Fahrenheit). Temperature test range: -40°C-150°C (-40°F-302°F). 0.1°C (-40°C-99.9°C), 1°C (100°C-150°C). 0.1°F (-40°F-99.9°F), 1°F (100°F-302°F). Temperature test accuracy: +/- 0.5 °C + 2dgt +/- 0.9 °F + 2dgt. Power Supplies: 4 X 1.5V SIZE. AA / LR6 Battery not include. Ancel AC3000 refrgerantion Digital Manifold Gauge. Clamp on temperature probe socket. 5, R+/R-Refrigerant Type Selection Buttons. 10, High Pressure Button. 11, Refrigerant Obezervation Window. 12, Pressure release valve. 13, Refrigerant inlet/vacuum Pump inlet. 14, Low Pressure Valve. 15,1/4 inch high pressure inlet. 1 x AC3000 Manifold Digital Meter. 1 x Paper Box. 1 x User Manual. Clean the exterior with a damp cloth. Do not use harsh solvents. Keep screw connections clean and free of grease, clean with a moist cloth as required. Carefully blow out oil residues in valve block using compressed air. Replace the batteries when low battery power indication lights on in LCD. Low battery power supply. The instruments has low power sign. When it is displayed, it means the battery power is insufficient. At this time, the battery should be replaced as required in order to avoid affecting normal use. Damaged refrigerant hose orvalve stem. Please check the pipe connections and hoses before testing. If you find any damage, please replace them immediately to avoid improper use or accident. Failure of refrigerant filling. There is a valve core in the refrigerant inlet of the refrigeration system. When connecting the instrument, pay attention the two terminals of the hoses. Connect one terminal with a core to the refrigeration system, while another terminal without acore to the instrument. Every hose terminal comes with a nylonpad that is limited a certain life of using. Over use or other situation will make itdefective, which result in leakage. The instrument refrigerant inlet (the middle port of the instrument) has a port with valve core, which is used to vent the air in the hoes after connecting the refrigerant to the instrument. The port is equipped with a copper plug screw. It is required to tighten it every time before or after operation. Check the refrigeration system’s pipes and connectors. Credit cards? Debit card? Apple Pay? Google Pay ect. Carrier and Logistics: All Orders are. Free repair for the devices. OBDII Code Reader, Car Diagnostic Tool, Truck Diagnostic Tool, EVAP Smoke Machine, Car Power Probe, Battery Tester. The price is reasonable and we have top rated after-sales service. Our main brand is. And we also sell other brands product, such as. FOXWELL, LAUNCH, THINKCAR, AUTOPHIX. GMT8 (9:00-18:00). From Monday to Friday.
ANCEL AC3000 Air Conditioning Digital Vacuum Gauge Meter Refrigerant Leak Teste. About the Ancel AC3000. Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-time Display with Optional Two Clamp-on Temperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /°F Conversion. It is the right one you have to do the job right. Please Read this manual carefully and familiarize yourself with the instrument before operating it, Pay particular attention to the safety instructions and warning advice in order to prevent injuries and damage to the product. 1 The pressure measured by this digital manifold pressure tester is gauge pressure. 2The pressure test range is from -101Kpa to 6Mpa(-0.1bar to 60bar). 3The limit pressure is 10Mpa (100bar). 4The maximum working pressure of the standard hose is 600 PSI approx. 4.13 Mpa, 41.3 bar. The limit pressure is 3000 PSI approx. 20.68 Mpa, 206.8 bar. 5Please confirm the rated pressure value of the tested device before testing. Do not use it if it exceeds the range of the device. If the packaged hoses do not meet the pressure requirements, you can also use suitable replacement hoses for the test. 6 Do not use and store the instrument in high temperatures, high humidity, flammable or explosive materials, or in strong electromagnetic fields. 7 Do not modify the internal circuits of the device to avoid damaging the device or endangering it. 8 Please wear qualified protective equipment during testing. 9 Please use the instrument in a well-ventilated environment to prevent inhalation of toxic gases. Turn off the blue valve and red valve. Turn on the instrument. Then verify that LCD displays the status of the pressure test, as shown in the figure below. If not, press the function button to switch it. When the instrument is turned on, there may be 10 digits in the high and low. Press R+/ R- buttons, Unit button and’C/OF button to select tested refrigerant and reading display respectively. If the clamp-on temperature probes have been connected to the instrument, ethereal-time temperature will be displayed. If not, no display of it. Connect the instrument to the. Refrigeration system according to the chart below. Turn on the refrigerant valve and gently press the pressure release valve to vent the air in the connecting hose. When the refrigeration system stops, turn on the high pressure valve (red valve)and fill with a certain amount of refrigerant and then shut the valve quickly. Run the refrigeration system, turn on the low pressure valve (blue valve), and fill with the refrigerant into the refrigeration system. After the filling is completed, shut the low pressure valve (blue valve) and refrigerant valve. Let the refrigeration system running. Shut down the refrigeration system, make sure all valves are turned off, then disconnect the instrument between refrigeration system and source. Do not remove the high pressure valve connection until the pressure drops to the safe point. Then turn off the instrument. Open the battery compartment by squeezing the clip lock. Close the battery compartment. Connect Clamp-on Temperature Probes(Optional). Real-time temperature measuring requires two clamp-on temperature probes connected to the sockets on top of the instrument, which further enable instrument calculate superheat and subcooling simultaneously. Credit cards? Debit card? Apple Pay? Google Pay. 3 months for the accessories. The price is reasonable and we have top rated after-sales service. Our main brand is ANCEL, and we also sell other brands product, such as FOXWELL, LAUNCH, THINKCAR, AUTOPHIX, etc. GMT8 (9:00-18:00) from Monday to Friday. ANCEL AC3000 HVAC Refrigeration Tools Gauges. Manifold, Gauge & Hose Set. Dual pressure test, dual temperature test. Digital display direct reading, multi-unit switching. Vacuum pumping, pressure maintaining. Monitoring the high and low pressure. Leak detection, filling refrigeration liquid. Multi-mode function and built-in refrigerant database. Dual channel pressure (gauge pressure). Built-in 32-bit digital processing unit. Double channel temperature measurement. Cars, motorcycles, lawn mowers, ATVs. Lawn tractors, trucks, SUVs, boats, PWCs, classic cars, and more. Built in 92 kinds of refrigerant pressure. Leakage Time And Speed Recording. Pressure, Temperature, Test, Vacuum. R-134a, R-12, R-1234yf, R-123, R-12a, R-22, R-290. 101 Kpa – 0 Kpa. +/- 0.5 °C + 2dgt +/- 0.9 °F + 2dgt. 10000 Kpa (10 Mpa, 100 bar,). Kpa, Mpa, bar, inHg, PSI. 0 Kpa – 6000 Kpa. +/- 0.5 %(FS)+ 5dgt. 4 X 1.5V SIZE. AA / LR6 Battery not include.