Extreme Ultra 6 X 6Ml, Air Conditioning and Refrigeration Leak Stop

Posts Tagged ‘leak’

Extreme Ultra 6 X 6Ml, Air Conditioning and Refrigeration Leak Stop

Posted by admin at October 2, 2024

Category: extreme

Tags: conditioning, extreme, leak, refrigeration, stop, ultra

Extreme Ultra 6 X 6Ml, Air Conditioning and Refrigeration Leak Stop

PERMANENT REPAIR : it permanently seals refrigerant leaks up to 0. 3 mm in air conditioning and refrigeration systems. ACTS QUICKLY on rubber and metal components of A / C systems. Compatible with ANY REFRIGERATION LUBRICANTS AND REFRIGERANT GASES, excluding Ammonia (R717). SAFE for the system thanks to its polymer – free formulation ; does not block AC / R components and does not react with moisture and oxygen. INCLUDES REUSABLE 1 / 4 SAE and 5 / 16 SAE ADAPTERS. DOSE : 6 mL is the universal dose for air conditioning and refrigeration systems up to 21 kW (or 700 mL of compressor lubricant). 9 out of 5 stars. Leak stop specific for. 1 cartridge of leak stop + 1 1 / 4 SAE adapter. 1 cartridge of leak stop + 1 5 / 16 SAE adapter. 1 cartridge of leak stop + 1 R1234yf adapter. 1 cartridge of leak stop + 1 R134a adapter. 1 cartridge of leak stop. 1 cartridge for systems up to 21 kW or 700 ml of compressor oil. 1 cartridge for one vehicle. 1 cartridge for systems up to 21 kW or 700 ml of compressor oil (HVAC) or for one vehicle (Automotive).

No Comments

Air Conditioning Refrigeration Detector LD-200 Handheld Infrared Leak Detector

Posted by admin at September 3, 2024

Category: conditioning

Tags: conditioning, detector, handheld, infrared, ld-200, leak, refrigeration

Air Conditioning Refrigeration Detector LD-200 Handheld Infrared Leak Detector

Report Item / Suspicious Activity. Heated Diode Refrigerant Leak Detector LD-200 Handheld Leak Tester Air Conditioning Refrigeration System Detect Tool. The LD-200 is a hand-held leak detector that uses the heated diode detection. Compared with the traditional leak detector, its sensor has longer life, higher detection accuracy, easy to operate and can detect a wider range of refrigerant. LD-200 is equipped with large LCD screen, so that the test results are more intuitive. The exclusive design of appearance is in accordance with human body mechanics to make it the best experience for users. Charging current:5VDC 1A. Sensor principle: heated diode. Sensor life: 10 years. Sensitivity: max 4g/ yr. Alarm mode: sound and light alarm, LCD display. Battery: built-in rechargeable lithium battery 3.7V 3000mAhWorking time:continuous 6H. Operating environment:-10 C -52 C relative humidity (50%85% RH)Storage temperature:-20. Weight: 415g(14.6oz). Size: 201mm 86mm 38mm (7.9″ 3.3″ 1.5). It responds to ALL halogenated (containing chlorine or fluorine) refrigerants, including. R11, R12, R500, R503 etc. R22, R123, R124, R502. Blends including AZ-50, HP62, MP39 etc. Detect ethylene oxide gas leaks in hospital sterilizing equipment. Detect SF-6 in high voltage circuit breakers. Detect most gasses that contain chlorine, fluorine and bromine (halogen gasses). Detects cleaning agents used when dry cleaning such as perchloroethy. Detects halogen gasses in fire extinguishing systems. Maximum sensitivity is less than 4g / yr. L- M- H, three levels of sensitivity adjustment. Self-test function starts once power on. Leakage peak recording function. LCD display, display the leakage more intuitively. Shut off the hardware circuit function so that the battery can be used for. Open or close the buzzer in on button and can apply to all occasions. Built-inhigh-capacity rechargeablelithium battery ismoreenvironmentally. Friendly and has longer service life. Flexible probe, can used to detect in a narrow space. 1 x Halogen leak detector with probe. 1 x Instruction sheet. 1 x Black carrying box.

No Comments

UK Digital Manifold Gauge A/C Refrigeration Diagnostic Vacuum Pressure Leak Test

Posted by admin at August 29, 2024

Category: digital

Tags: diagnostic, digital, gauge, leak, manifold, pressure, refrigeration, test, vacuum

UK Digital Manifold Gauge A/C Refrigeration Diagnostic Vacuum Pressure Leak Test

ANCEL AC3000 digital manifold is a professisional instrument for installation, testing and maintenance of refrigeration equipment suchas air conditioners and cold stores. It combines 2-way pressure test, dual temperature measurements (with optionaldual temperature probes), a 32-bit digitalprocessor and a large LCD in one easy-to-useinstrument with the following main functions. Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-timeSuperheat and Subcooling Simultaneously Display with Optional Two Clamp-onTemperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /? Conversion. It is the right one you have to do the job right. Turn off the blue valve and red valve. Turn on the instrument. Then verify that LCD displays the status of the pressure test. If not, press the function button to switch it. When the instrument is turned on, theremay be 10 digits in the high and low pressure display area. Press R+/ R- buttons, Unit button and? /? Button to select tested refrigerant and reading display respectively. If the clamp-on temperature probes havebeen connected to the instrument, the real-time temperature will be displayed. If not, no display of it. Connect the instrument to the refrigeration system according to thechart below. Turn on the refrigerant valve and gently press the pressure release valve to vent the air in the connecting hose. When the refrigeration system stops, turnon the high pressure valve (red valve) and fill with a certain amount of refrigerant and then shut the valve quickly. Run the refrigeration system, turn on the low pressure valve (blue valve), and fill with the refrigerant into the refrigeration system. After the filling is completed, shut the low pressure valve (blue valve) and refrigerant valve. Let the refrigeration system running. Shut down the refrigeration system, make sure all valves are turned off, then disconnect the instrument between refrigeration system and source. Do not remove the high pressure valve connection until the pressure drops to the safe point. Then turn off the instrument. The filling operation of different equipment or refrigerants may vary. Please read carefully the relevant specific operation requirements for filling operation, so as to avoid damage to user or equipment caused by improper operation! The instrument can display the corresponding Evaporation Temperature(EV) and Condensation Temperature (CO) during the refrigerant pressure test. If the clamp-on temperature probes are connected to the instrument, LCD will display the real-time temperature in the spot T1 Sensor and T2 Sensor. Please make sure clamp-on temperature probes are connected as step 6 and contacted fully to the refrigeration pipes. The instrument can calculate the SH-Superheat and SC – Subcooling as long as the tested refrigerant ispreset and clamp-on temperature probes are connected well. Power on the instrument. Then make surethe LCD displays vacuum test status. If not, press the Function button to switch it. When the instrument is turned on, there may be 10 digits in the high and low pressure display area. Press the unit button to adjust the reading unit. Connect the instrument to the refrigeration system. Connected clamp-on temperature probes will not affect the operation. Turn on the blue valve and red valve, andstart the vacuum pump. After the vacuum operation is completed, turn off the blue valve and red valve, then shut the vacuum pump. At this time, pressure leak test mode can be used to check leakage in the system (Please refer to Pressure Leak Test). The instrument is powered on with the blue and red valves turned off. Press the Function button to pressure leak test mode. The current pressure value is displayed at lower rightcorner of LCD. Press the Run/Stop button to start the leak test. At this time, the lower left corner records the initial pressure value; the lower right corner displays the instantaneous pressure value; the “P” display area shows the difference between the initial pressure value and the instantaneous pressure value. The time display shows how long the leak test will take, in hour : minute (HH:MM)format. All pressure units on the screen are the same. You can switch between the different pressure units by pressing the Unit button. 89 Kids of Refrigeant Database. Built-in 89 kinds of refrigerant NIST: According to AmericanNIST standard. R11 R113 R114 R115 R116 R12 R123 R124 R125 R1270. R13 R134A R14 R141B R142B R143A R152A R170 R21 R218. R22 R227EA R23 R236EA R245CA R245FA R290 R32 R401A R401B. R401C R402A R402B R403A R403B R404A R405A R406A R407A R407B. R407C R407D R407E R408A R409A R409B R41 R410A R410B R411A. R411B R412A R413A R414A R414B R415A R415B R416A R417A R418A. R419A R420A R421A R421B R422A R422B R422C R422D R423A R424A. R425A R426A R427A R428A R50 R500 R501 R502 R503 R504. R507A R508A R507B R509A R600 R600A R707 R7441C02 R1234. Wide Range of applications. Pressure test: gauge pressure. Pressure test unit: Kpa; Mpa; bar; inHg; PSI. Pressure test range: 0 Kpa – 6000 Kpa. Pressure test resolution: 1 Kpa. Pressure test accuracy: +/- 0.5 %(FS)+ 5dgt. Pressure overload limit: 10000 Kpa (10 Mpa; 100 bar;). Vacuum test: relative vacuum. Vacuum test unit: Kpa; Mpa; bar; inHg; PSI. Vacuum test range: -101 Kpa – 0 Kpa. Vacuum test resolution: 1 Kpa. Temperature test unit: °C (Celsius), °F (Fahrenheit). Temperature test range: -40°C-150°C (-40°F-302°F). 0.1°C (-40°C-99.9°C), 1°C (100°C-150°C). 0.1°F (-40°F-99.9°F), 1°F (100°F-302°F). Temperature test accuracy: +/- 0.5 °C + 2dgt +/- 0.9 °F + 2dgt. Power Supplies: 4 X 1.5V SIZE. AA / LR6 Battery not include. Ancel AC3000 refrgerantion Digital Manifold Gauge. Clamp on temperature probe socket. 5, R+/R-Refrigerant Type Selection Buttons. 10, High Pressure Button. 11, Refrigerant Obezervation Window. 12, Pressure release valve. 13, Refrigerant inlet/vacuum Pump inlet. 14, Low Pressure Valve. 15,1/4 inch high pressure inlet. 1 x AC3000 Manifold Digital Meter. 1 x Paper Box. 1 x User Manual. Clean the exterior with a damp cloth. Do not use harsh solvents. Keep screw connections clean and free of grease, clean with a moist cloth as required. Carefully blow out oil residues in valve block using compressed air. Replace the batteries when low battery power indication lights on in LCD. Low battery power supply. The instruments has low power sign. When it is displayed, it means the battery power is insufficient. At this time, the battery should be replaced as required in order to avoid affecting normal use. Damaged refrigerant hose orvalve stem. Please check the pipe connections and hoses before testing. If you find any damage, please replace them immediately to avoid improper use or accident. Failure of refrigerant filling. There is a valve core in the refrigerant inlet of the refrigeration system. When connecting the instrument, pay attention the two terminals of the hoses. Connect one terminal with a core to the refrigeration system, while another terminal without acore to the instrument. Every hose terminal comes with a nylonpad that is limited a certain life of using. Over use or other situation will make itdefective, which result in leakage. The instrument refrigerant inlet (the middle port of the instrument) has a port with valve core, which is used to vent the air in the hoes after connecting the refrigerant to the instrument. The port is equipped with a copper plug screw. It is required to tighten it every time before or after operation. Check the refrigeration system’s pipes and connectors. About Invoices: If an. Much appreciated to leave us your. ANCEL specializes in automotive intelligent diagnostics, detection and analysis systems, and automotive-related products for mechanics, repair shops, and DIYers. Our independent brand is. FOXWELL, LAUNCH, AUTOPHIX, OBDPROG ect. If there are any after-sales or pre-sales messages that can be sent to us, we will promptly handle them and provide satisfactory solutions. Model, make year, VIN. And tell me the main problem of your car, we will check and recommend a suitable product for you. Any questions, Please feel free to.

No Comments

5 Pieces Gas Leak Detector Refrigerant for Air Conditioning Household

Posted by admin at August 9, 2024

Category: pieces

Tags: conditioning, detector, household, leak, pieces, refrigerant

5 Pieces Gas Leak Detector Refrigerant for Air Conditioning Household

Pot Plants Indoor Planters for Wooden Flower Stand Flowers Household. 4 Sheets glass lure eyes Fishing Bait Eyes Stick On Fish Eyes Fly Tying. 2 Pcs Hamster Platform Wooden Table Play Gym Small Animal Toys. Water dog Dog Water Dispenser Dog Kennels and Crates for. School of Fish Wall Art Metal Fish Wall Art Metal Fish Wall Pendant Statue. 1Pc cockatiel toys Chicken Mirror Toy Chicken Bell for Coop Hen. Collecting listings has surprises. Description The exquisite craftsmanship can serve you well without breaking easily. The refrigerant leak detector is convenient and practical, with excellent texture, and can serve you for a long time without being easily damaged. This is a very practical refrigerant leak detector Features -Color: Yellow -Material: ABS -Size: 22.90X6.50X6.50cm/9.00X2.55X2.55in Working temperature: 0-52 Celsius degree Probe length: 20cm – When the leaked gas is found, the warning sound will become more rapid, and the more leakage, the more rapid the warning sound. At the same time, the indicator light flashes quickly. Maximum sensitivity: For halogen refrigerant, 6gr/ Power supply: 4 x AAA batteries (not included) Battery Life: About 50 hours under normal use Response Time: Instantaneous – Auto-following circuit: When the instrument is in the detection state, the automatic circuit will follow the halogen in the environment. Changes in the concentration of the element gas to prevent false alarms. Mode: unlimited – Sensitivity adjustment: This product has the function of stepless adjustment of sensitivity, which can be adjusted at any time during detection. When the refrigerant concentration level is reached, it enters the detection state. If the user turns on the look for sources of higher concentrations of leaks. The instrument can also be turned on in clean air to adjust to maximum sensitivity, at which point leaks above the zero concentration level can be detected. Power-on reset: After the instrument is turned on, it can automatically adjust the circuit within 6S to ignore the existing probe. Warm-up time: about Reset time: 2-10 seconds Refrigerant Gas Detector. 5 x refrigerant leak detector. People Who Viewed This Item Also Viewed. 30 Pcs Refrigerant Filling Valve Accessories Refrigeration Valves. 24Pcs Sponge Foam Brush Dabbers Wooden Handle Craft for Art Painting Drawing New. Flush Actuator Water Tank Button Toilet Flushing Accessories. Large Computer Desk Corner Laptop PC Table Home Office Workstation +4 Shelves. Blow Up Walking Stick Costume Cosplay Supplies Inflatable Walking Stick. 2Pcs Handrail End Caps for Wood Stair Rail (38MM). 2Pcs 90 Degree Brass Air Tyre Valve Stem with Extension Adapter for Car Truck. 20 Pcs hat key wall hooks Key Coat Hanger Single Coat Hooks Small Hook Wall. Open sign LED neon for wall LED Open Neon Sign Open Neon Light Led Neon Open. 250Pcs /1Roll Self Adhesive Paper Reactive Splatter Shooting Stickers. Perpetual Desk Calendar with Clock Manual Desktop Calendar Digital Date Month. 10 Sheets Creative Plastic Heat Shrinky Sheets Heat Shrink Paper. Handheld stitcher Quickly Repair Sewing Machine Kids Cloth DIY. 1 Box Rainbow Color Embroidery Floss Embroidery Thread. 12PCS Cute Small Mushroom Christmas Tree Ornament Xmas Home Party DIY Decoration. Retractable Keychain Badge Reel with Carabiner Belt Clip Steel Cable Key Ring. 12pcs Nontoxic Creative Dog Balls Pet Supplies Puppy Toys Tennis Balls. Dog Puzzle Toy Ball Dog Treat Toy Dog Puzzle Feeder Puzzle Dog Toys Dog Toys. Long Plastic Handle Nature Ostrich Duster Feather Dusters Cleaning Tool Home. Adjustable tree stand Stable Holiday Christmas Tree Holder Base Christmas Tree. 50pcs face sponge Pads Compressed Facial Sponge Reusable Cosmetic Puff. 4Pcs/Stet Carving Tools Carpenter Tool Curved Wood Chisel Woodworking Tools. Paper lamp shade hanging Paper Lamp Shade Hanging Square Square.

No Comments

Digital Manifold Gauge A/C Temperature Diagnostic Tool Vacuum Pressure Leak Test

Posted by admin at August 5, 2024

Category: digital

Tags: diagnostic, digital, gauge, leak, manifold, pressure, temperature, test, tool, vacuum

Digital Manifold Gauge A/C Temperature Diagnostic Tool Vacuum Pressure Leak Test

ANCEL AC3000 digital manifold is a professisional instrument for installation, testing and maintenance of refrigeration equipment suchas air conditioners and cold stores. It combines 2-way pressure test, dual temperature measurements (with optionaldual temperature probes), a 32-bit digitalprocessor and a large LCD in one easy-to-useinstrument with the following main functions. Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-timeSuperheat and Subcooling Simultaneously Display with Optional Two Clamp-onTemperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /? Conversion. It is the right one you have to do the job right. Turn off the blue valve and red valve. Turn on the instrument. Then verify that LCD displays the status of the pressure test. If not, press the function button to switch it. When the instrument is turned on, theremay be 10 digits in the high and low pressure display area. Press R+/ R- buttons, Unit button and? /? Button to select tested refrigerant and reading display respectively. If the clamp-on temperature probes havebeen connected to the instrument, the real-time temperature will be displayed. If not, no display of it. Connect the instrument to the refrigeration system according to thechart below. Turn on the refrigerant valve and gently press the pressure release valve to vent the air in the connecting hose. When the refrigeration system stops, turnon the high pressure valve (red valve) and fill with a certain amount of refrigerant and then shut the valve quickly. Run the refrigeration system, turn on the low pressure valve (blue valve), and fill with the refrigerant into the refrigeration system. After the filling is completed, shut the low pressure valve (blue valve) and refrigerant valve. Let the refrigeration system running. Shut down the refrigeration system, make sure all valves are turned off, then disconnect the instrument between refrigeration system and source. Do not remove the high pressure valve connection until the pressure drops to the safe point. Then turn off the instrument. The filling operation of different equipment or refrigerants may vary. Please read carefully the relevant specific operation requirements for filling operation, so as to avoid damage to user or equipment caused by improper operation! The instrument can display the corresponding Evaporation Temperature(EV) and Condensation Temperature (CO) during the refrigerant pressure test. If the clamp-on temperature probes are connected to the instrument, LCD will display the real-time temperature in the spot T1 Sensor and T2 Sensor. Please make sure clamp-on temperature probes are connected as step 6 and contacted fully to the refrigeration pipes. The instrument can calculate the SH-Superheat and SC – Subcooling as long as the tested refrigerant ispreset and clamp-on temperature probes are connected well. Power on the instrument. Then make surethe LCD displays vacuum test status. If not, press the Function button to switch it. When the instrument is turned on, there may be 10 digits in the high and low pressure display area. Press the unit button to adjust the reading unit. Connect the instrument to the refrigeration system. Connected clamp-on temperature probes will not affect the operation. Turn on the blue valve and red valve, andstart the vacuum pump. After the vacuum operation is completed, turn off the blue valve and red valve, then shut the vacuum pump. At this time, pressure leak test mode can be used to check leakage in the system (Please refer to Pressure Leak Test). The instrument is powered on with the blue and red valves turned off. Press the Function button to pressure leak test mode. The current pressure value is displayed at lower rightcorner of LCD. Press the Run/Stop button to start the leak test. At this time, the lower left corner records the initial pressure value; the lower right corner displays the instantaneous pressure value; the “P” display area shows the difference between the initial pressure value and the instantaneous pressure value. The time display shows how long the leak test will take, in hour : minute (HH:MM)format. All pressure units on the screen are the same. You can switch between the different pressure units by pressing the Unit button. 89 Kids of Refrigeant Database. Built-in 89 kinds of refrigerant NIST: According to AmericanNIST standard. R11 R113 R114 R115 R116 R12 R123 R124 R125 R1270. R13 R134A R14 R141B R142B R143A R152A R170 R21 R218. R22 R227EA R23 R236EA R245CA R245FA R290 R32 R401A R401B. R401C R402A R402B R403A R403B R404A R405A R406A R407A R407B. R407C R407D R407E R408A R409A R409B R41 R410A R410B R411A. R411B R412A R413A R414A R414B R415A R415B R416A R417A R418A. R419A R420A R421A R421B R422A R422B R422C R422D R423A R424A. R425A R426A R427A R428A R50 R500 R501 R502 R503 R504. R507A R508A R507B R509A R600 R600A R707 R7441C02 R1234. Wide Range of applications. Pressure test: gauge pressure. Pressure test unit: Kpa; Mpa; bar; inHg; PSI. Pressure test range: 0 Kpa – 6000 Kpa. Pressure test resolution: 1 Kpa. Pressure test accuracy: +/- 0.5 %(FS)+ 5dgt. Pressure overload limit: 10000 Kpa (10 Mpa; 100 bar;). Vacuum test: relative vacuum. Vacuum test unit: Kpa; Mpa; bar; inHg; PSI. Vacuum test range: -101 Kpa – 0 Kpa. Vacuum test resolution: 1 Kpa. Temperature test unit: °C (Celsius), °F (Fahrenheit). Temperature test range: -40°C-150°C (-40°F-302°F). 0.1°C (-40°C-99.9°C), 1°C (100°C-150°C). 0.1°F (-40°F-99.9°F), 1°F (100°F-302°F). Temperature test accuracy: +/- 0.5 °C + 2dgt +/- 0.9 °F + 2dgt. Power Supplies: 4 X 1.5V SIZE. AA / LR6 Battery not include. Ancel AC3000 refrgerantion Digital Manifold Gauge. Clamp on temperature probe socket. 5, R+/R-Refrigerant Type Selection Buttons. 10, High Pressure Button. 11, Refrigerant Obezervation Window. 12, Pressure release valve. 13, Refrigerant inlet/vacuum Pump inlet. 14, Low Pressure Valve. 15,1/4 inch high pressure inlet. 1 x AC3000 Manifold Digital Meter. 1 x Paper Box. 1 x User Manual. Clean the exterior with a damp cloth. Do not use harsh solvents. Keep screw connections clean and free of grease, clean with a moist cloth as required. Carefully blow out oil residues in valve block using compressed air. Replace the batteries when low battery power indication lights on in LCD. Low battery power supply. The instruments has low power sign. When it is displayed, it means the battery power is insufficient. At this time, the battery should be replaced as required in order to avoid affecting normal use. Damaged refrigerant hose orvalve stem. Please check the pipe connections and hoses before testing. If you find any damage, please replace them immediately to avoid improper use or accident. Failure of refrigerant filling. There is a valve core in the refrigerant inlet of the refrigeration system. When connecting the instrument, pay attention the two terminals of the hoses. Connect one terminal with a core to the refrigeration system, while another terminal without acore to the instrument. Every hose terminal comes with a nylonpad that is limited a certain life of using. Over use or other situation will make itdefective, which result in leakage. The instrument refrigerant inlet (the middle port of the instrument) has a port with valve core, which is used to vent the air in the hoes after connecting the refrigerant to the instrument. The port is equipped with a copper plug screw. It is required to tighten it every time before or after operation. Check the refrigeration system’s pipes and connectors. Greenwich Mean Time will be delivered on the same day! 12 months free repair for the devices. 3 months for the accessories. The price is reasonable and we have top rated after-sales service. Our agent brands are: ANCEL, FOXWELL, LAUNCH, THINKCAR, AUTOPHIX, etc. We promise to help you solve it asap, and make you feel satisfactory absolutely. After you received our package you are satisfied with it. We will do the same as soon as we can too.

No Comments

Manifold Digital Meter Temperature Gauge Air-Condition Vacuum Pressure Leak Test

Posted by admin at July 6, 2024

Category: manifold

Tags: air-condition, digital, gauge, leak, manifold, meter, pressure, temperature, test, vacuum

Manifold Digital Meter Temperature Gauge Air-Condition Vacuum Pressure Leak Test

ANCEL AC3000 digital manifold is a professisional instrument for installation, testing and maintenance of refrigeration equipment suchas air conditioners and cold stores. It combines 2-way pressure test, dual temperature measurements (with optionaldual temperature probes), a 32-bit digitalprocessor and a large LCD in one easy-to-useinstrument with the following main functions. Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-timeSuperheat and Subcooling Simultaneously Display with Optional Two Clamp-onTemperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /? Conversion. It is the right one you have to do the job right. Turn off the blue valve and red valve. Turn on the instrument. Then verify that LCD displays the status of the pressure test. If not, press the function button to switch it. When the instrument is turned on, theremay be 10 digits in the high and low pressure display area. Press R+/ R- buttons, Unit button and? /? Button to select tested refrigerant and reading display respectively. If the clamp-on temperature probes havebeen connected to the instrument, the real-time temperature will be displayed. If not, no display of it. Connect the instrument to the refrigeration system according to thechart below. Turn on the refrigerant valve and gently press the pressure release valve to vent the air in the connecting hose. When the refrigeration system stops, turnon the high pressure valve (red valve) and fill with a certain amount of refrigerant and then shut the valve quickly. Run the refrigeration system, turn on the low pressure valve (blue valve), and fill with the refrigerant into the refrigeration system. After the filling is completed, shut the low pressure valve (blue valve) and refrigerant valve. Let the refrigeration system running. Shut down the refrigeration system, make sure all valves are turned off, then disconnect the instrument between refrigeration system and source. Do not remove the high pressure valve connection until the pressure drops to the safe point. Then turn off the instrument. The filling operation of different equipment or refrigerants may vary. Please read carefully the relevant specific operation requirements for filling operation, so as to avoid damage to user or equipment caused by improper operation! The instrument can display the corresponding Evaporation Temperature(EV) and Condensation Temperature (CO) during the refrigerant pressure test. If the clamp-on temperature probes are connected to the instrument, LCD will display the real-time temperature in the spot T1 Sensor and T2 Sensor. Please make sure clamp-on temperature probes are connected as step 6 and contacted fully to the refrigeration pipes. The instrument can calculate the SH-Superheat and SC – Subcooling as long as the tested refrigerant ispreset and clamp-on temperature probes are connected well. Power on the instrument. Then make surethe LCD displays vacuum test status. If not, press the Function button to switch it. When the instrument is turned on, there may be 10 digits in the high and low pressure display area. Press the unit button to adjust the reading unit. Connect the instrument to the refrigeration system. Connected clamp-on temperature probes will not affect the operation. Turn on the blue valve and red valve, andstart the vacuum pump. After the vacuum operation is completed, turn off the blue valve and red valve, then shut the vacuum pump. At this time, pressure leak test mode can be used to check leakage in the system (Please refer to Pressure Leak Test). The instrument is powered on with the blue and red valves turned off. Press the Function button to pressure leak test mode. The current pressure value is displayed at lower rightcorner of LCD. Press the Run/Stop button to start the leak test. At this time, the lower left corner records the initial pressure value; the lower right corner displays the instantaneous pressure value; the “P” display area shows the difference between the initial pressure value and the instantaneous pressure value. The time display shows how long the leak test will take, in hour : minute (HH:MM)format. All pressure units on the screen are the same. You can switch between the different pressure units by pressing the Unit button. 89 Kids of Refrigeant Database. Built-in 89 kinds of refrigerant NIST: According to AmericanNIST standard. R11 R113 R114 R115 R116 R12 R123 R124 R125 R1270. R13 R134A R14 R141B R142B R143A R152A R170 R21 R218. R22 R227EA R23 R236EA R245CA R245FA R290 R32 R401A R401B. R401C R402A R402B R403A R403B R404A R405A R406A R407A R407B. R407C R407D R407E R408A R409A R409B R41 R410A R410B R411A. R411B R412A R413A R414A R414B R415A R415B R416A R417A R418A. R419A R420A R421A R421B R422A R422B R422C R422D R423A R424A. R425A R426A R427A R428A R50 R500 R501 R502 R503 R504. R507A R508A R507B R509A R600 R600A R707 R7441C02 R1234. Wide Range of applications. Pressure test: gauge pressure. Pressure test unit: Kpa; Mpa; bar; inHg; PSI. Pressure test range: 0 Kpa – 6000 Kpa. Pressure test resolution: 1 Kpa. Pressure test accuracy: +/- 0.5 %(FS)+ 5dgt. Pressure overload limit: 10000 Kpa (10 Mpa; 100 bar;). Vacuum test: relative vacuum. Vacuum test unit: Kpa; Mpa; bar; inHg; PSI. Vacuum test range: -101 Kpa – 0 Kpa. Vacuum test resolution: 1 Kpa. Temperature test unit: °C (Celsius), °F (Fahrenheit). Temperature test range: -40°C-150°C (-40°F-302°F). 0.1°C (-40°C-99.9°C), 1°C (100°C-150°C). 0.1°F (-40°F-99.9°F), 1°F (100°F-302°F). Temperature test accuracy: +/- 0.5 °C + 2dgt +/- 0.9 °F + 2dgt. Power Supplies: 4 X 1.5V SIZE. AA / LR6 Battery not include. Ancel AC3000 refrgerantion Digital Manifold Gauge. Clamp on temperature probe socket. 5, R+/R-Refrigerant Type Selection Buttons. 10, High Pressure Button. 11, Refrigerant Obezervation Window. 12, Pressure release valve. 13, Refrigerant inlet/vacuum Pump inlet. 14, Low Pressure Valve. 15,1/4 inch high pressure inlet. 1 x AC3000 Manifold Digital Meter. 1 x Paper Box. 1 x User Manual. Clean the exterior with a damp cloth. Do not use harsh solvents. Keep screw connections clean and free of grease, clean with a moist cloth as required. Carefully blow out oil residues in valve block using compressed air. Replace the batteries when low battery power indication lights on in LCD. Low battery power supply. The instruments has low power sign. When it is displayed, it means the battery power is insufficient. At this time, the battery should be replaced as required in order to avoid affecting normal use. Damaged refrigerant hose orvalve stem. Please check the pipe connections and hoses before testing. If you find any damage, please replace them immediately to avoid improper use or accident. Failure of refrigerant filling. There is a valve core in the refrigerant inlet of the refrigeration system. When connecting the instrument, pay attention the two terminals of the hoses. Connect one terminal with a core to the refrigeration system, while another terminal without acore to the instrument. Every hose terminal comes with a nylonpad that is limited a certain life of using. Over use or other situation will make itdefective, which result in leakage. The instrument refrigerant inlet (the middle port of the instrument) has a port with valve core, which is used to vent the air in the hoes after connecting the refrigerant to the instrument. The port is equipped with a copper plug screw. It is required to tighten it every time before or after operation. Check the refrigeration system’s pipes and connectors. Credit cards? Debit card? Apple Pay? Google Pay ect. Carrier and Logistics: All Orders are. Free repair for the devices. OBDII Code Reader, Car Diagnostic Tool, Truck Diagnostic Tool, EVAP Smoke Machine, Car Power Probe, Battery Tester. The price is reasonable and we have top rated after-sales service. Our main brand is. And we also sell other brands product, such as. FOXWELL, LAUNCH, THINKCAR, AUTOPHIX. GMT8 (9:00-18:00). From Monday to Friday.

No Comments

ANCEL AC3000 Air Conditioning Digital Vacuum Gauge Meter Refrigerant Leak Teste

Posted by admin at June 28, 2024

Category: ancel

Tags: ac3000, ancel, conditioning, digital, gauge, leak, meter, refrigerant, teste, vacuum

ANCEL AC3000 Air Conditioning Digital Vacuum Gauge Meter Refrigerant Leak Teste

ANCEL AC3000 Air Conditioning Digital Vacuum Gauge Meter Refrigerant Leak Teste. About the Ancel AC3000. Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-time Display with Optional Two Clamp-on Temperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /°F Conversion. It is the right one you have to do the job right. Please Read this manual carefully and familiarize yourself with the instrument before operating it, Pay particular attention to the safety instructions and warning advice in order to prevent injuries and damage to the product. 1 The pressure measured by this digital manifold pressure tester is gauge pressure. 2The pressure test range is from -101Kpa to 6Mpa(-0.1bar to 60bar). 3The limit pressure is 10Mpa (100bar). 4The maximum working pressure of the standard hose is 600 PSI approx. 4.13 Mpa, 41.3 bar. The limit pressure is 3000 PSI approx. 20.68 Mpa, 206.8 bar. 5Please confirm the rated pressure value of the tested device before testing. Do not use it if it exceeds the range of the device. If the packaged hoses do not meet the pressure requirements, you can also use suitable replacement hoses for the test. 6 Do not use and store the instrument in high temperatures, high humidity, flammable or explosive materials, or in strong electromagnetic fields. 7 Do not modify the internal circuits of the device to avoid damaging the device or endangering it. 8 Please wear qualified protective equipment during testing. 9 Please use the instrument in a well-ventilated environment to prevent inhalation of toxic gases. Turn off the blue valve and red valve. Turn on the instrument. Then verify that LCD displays the status of the pressure test, as shown in the figure below. If not, press the function button to switch it. When the instrument is turned on, there may be 10 digits in the high and low. Press R+/ R- buttons, Unit button and’C/OF button to select tested refrigerant and reading display respectively. If the clamp-on temperature probes have been connected to the instrument, ethereal-time temperature will be displayed. If not, no display of it. Connect the instrument to the. Refrigeration system according to the chart below. Turn on the refrigerant valve and gently press the pressure release valve to vent the air in the connecting hose. When the refrigeration system stops, turn on the high pressure valve (red valve)and fill with a certain amount of refrigerant and then shut the valve quickly. Run the refrigeration system, turn on the low pressure valve (blue valve), and fill with the refrigerant into the refrigeration system. After the filling is completed, shut the low pressure valve (blue valve) and refrigerant valve. Let the refrigeration system running. Shut down the refrigeration system, make sure all valves are turned off, then disconnect the instrument between refrigeration system and source. Do not remove the high pressure valve connection until the pressure drops to the safe point. Then turn off the instrument. Open the battery compartment by squeezing the clip lock. Close the battery compartment. Connect Clamp-on Temperature Probes(Optional). Real-time temperature measuring requires two clamp-on temperature probes connected to the sockets on top of the instrument, which further enable instrument calculate superheat and subcooling simultaneously. Credit cards? Debit card? Apple Pay? Google Pay. 3 months for the accessories. The price is reasonable and we have top rated after-sales service. Our main brand is ANCEL, and we also sell other brands product, such as FOXWELL, LAUNCH, THINKCAR, AUTOPHIX, etc. GMT8 (9:00-18:00) from Monday to Friday. ANCEL AC3000 HVAC Refrigeration Tools Gauges. Manifold, Gauge & Hose Set. Dual pressure test, dual temperature test. Digital display direct reading, multi-unit switching. Vacuum pumping, pressure maintaining. Monitoring the high and low pressure. Leak detection, filling refrigeration liquid. Multi-mode function and built-in refrigerant database. Dual channel pressure (gauge pressure). Built-in 32-bit digital processing unit. Double channel temperature measurement. Cars, motorcycles, lawn mowers, ATVs. Lawn tractors, trucks, SUVs, boats, PWCs, classic cars, and more. Built in 92 kinds of refrigerant pressure. Leakage Time And Speed Recording. Pressure, Temperature, Test, Vacuum. R-134a, R-12, R-1234yf, R-123, R-12a, R-22, R-290. 101 Kpa – 0 Kpa. +/- 0.5 °C + 2dgt +/- 0.9 °F + 2dgt. 10000 Kpa (10 Mpa, 100 bar,). Kpa, Mpa, bar, inHg, PSI. 0 Kpa – 6000 Kpa. +/- 0.5 %(FS)+ 5dgt. 4 X 1.5V SIZE. AA / LR6 Battery not include.

No Comments

Air Conditioner Air Conditioning Refrigerant Leak Detector Refrigerant AC

Posted by admin at April 27, 2024

Category: conditioner

Tags: conditioner, conditioning, detector, leak, refrigerant

Air Conditioner Air Conditioning Refrigerant Leak Detector Refrigerant AC

Collecting listings has surprises. It is one of the best choices for you. Are you looking for a professional, yet affordable refrigerant leak detector? Are you in search of a sturdy, trustworthy tool that can do multiple jobs at once? If yes, look no further! Our refrigerant leak detector must meet your needs Features Warm-up time: about Response Time: Instantaneous – Fine workmanship, and sturdy, not easy to wear or tear, you deserve to have one. It has the function of power-on reset and automatic follow-up, which can ignore the concentration level of halogen gas in the environment. Reset time: 2-10 seconds Probe length: 20cm Power supply: 4 x AAA batteries (not included) – Built-in high-precision voltage regulator IC and the ultra-low power consumption design make the work more stable and the battery more. Working temperature: 0-52 Celsius degree – The sensitivity can be adjusted at any time, and the instrument can be automatically adjusted to the best detection state. Battery Life: About under normal use Maximum sensitivity: For halogen refrigerant, 6gr/ Mode: unlimited – Indicator lights on the front of the panel are used for leak warning and battery voltage indication. Color: Yellow -Material: ABS – Size: 15.00X4.50X3.50cm/5.89X1.77X1.38in. 1 x refrigerant leak detector.

No Comments

Air Conditioning Coolant Portable Air Conditioner Refrigerant Leak Detector

Posted by admin at March 26, 2024

Category: conditioning

Tags: conditioner, conditioning, coolant, detector, leak, portable, refrigerant

Air Conditioning Coolant Portable Air Conditioner Refrigerant Leak Detector

Sifter Scoop Detecting Kit Treasures Hunting Metal Detector Accessories. 10 Pcs Fly Fishing Strike Indicators Bobbers Tackle Thill Stops Trout Floats. 1Pc Sponge Cleaner Aquarium Glass Cleaner Fish Tank Cleaning Tools. 6 Rolls hotel wallpaper border Chair Rail Molding Edge Tailgate Ceiling Tile. 1 Pair Removable Shoe Buckles Decorative Shoe Clips Wedding Shoe Charms Bow. 3 Sets high visibility safety flags Scooter Flag Trailer Metal Child Bike. Collecting listings has surprises. It is one of the best choices for you. Are you looking for a professional, yet affordable refrigerant leak detector? Are you in search of a sturdy, trustworthy tool that can do multiple jobs at once? If yes, look no further! Our refrigerant leak detector must meet your needs Features Probe length: 20cm Battery Life: About 50 hours under normal use Response Time: Instantaneous Mode: unlimited Power supply: 4 x AAA batteries (not included) Maximum sensitivity: For halogen refrigerant, 6gr/ Reset time: 2-10 seconds Warm-up time: about 6 seconds – Indicator lights on the front of the panel are used for leak warning and battery voltage indication. Fine workmanship, durable and sturdy, not easy to wear or tear, you deserve to have one. High-precision voltage regulator IC and the ultra-low power consumption design make the work more stable and the battery more durable. The sensitivity can be adjusted at any time, and the instrument can be automatically adjusted to the best detection state. Working temperature: 0-52 Celsius degree – It has the function of power-on reset and automatic follow-up, which can ignore the concentration level of halogen gas in the environment. Color: Yellow -Material: ABS -Size: 22.90X6.50X6.50cm/9.00X2.55X2.55in. 5 x refrigerant leak detector. People Who Viewed This Item Also Viewed. Refrigerant Leak Detector Hvac Tools Clearance Halogen Tester Household. 3 Pieces Abs Refrigerant Detector R410a Hvac Tools Clearance. 3 Pcs Refrigerant Ball Valve Full Port Water Stop Shut off Copper Forged Corner. Brass Automatic Pressure Relief Deflation Valve Air Vent Mounting Pole Release. 2 Pcs Air Conditioning Safety Valve Versatilen Size The Refrigerant. Tubing Tool Bit Flare Expander Drill Hex Handle HVAC Tools Copper. 3 Pcs Valve Copper Compact Manifold Air Conditioning Refrigerant Valves. 20 Pcs Refrigerant Filling Access Valves Accessories Durability Refrigerator. 5pcs Fruit Mice Cat Toys Plush Toys Catnip Mouse Kitten Toys Cat Interactive. Range finder bag Golfing Rangefinder Case Rangefinder Bag Men Organizer Tray. Black Velvet Ring Insert Display Jewelry Storage Box Foam Holder Organizer Trays. 1 Pc laptop screen filter Anti Blue- Ray Film Laptop Screen Film Laptop. Wireless keyboard bag Keyboard Sleeve Pouch Keyboard Bag Diving Fabric Travel. 8pcs roller transfer bearings stick on wheels for furniture furniture caster. Beginner Guitar Practice Ukulele Plastic Guitar Toy Guitar For Beginner. Milk 20ML Measuring Scoops Ground Coffee Scoop. 12 Pcs Artificial Feathered Birds Ornament Glitter Ornaments Clip Hair Miss. Locking pin backings Pin Backings Pin Locks Backs Locking Pin Keepers Lock Pin. Toy Baby Carrier Reborn Doll Accessories Breathable Children’s Bag. 2 Pcs Bung Wash Plug Vibrant Muffler Dirt Bike Exhaust Silencer Pipe. 12 Pcs Braided Ring Knitting Rings Yarn Tension for Crochet Finger Split. Butterflies Habitat Cage Visible Insect Cage Insect Observation Cage. 36PCS Bra Extenders 3 Hooks Bra Hook Extender Extension Bra Fastener. Razor Travel Case Zipper Electric Shaver Storage Bag Protective Pouch.

No Comments

Manifold Digital Meter Temperature Gauge Air-Condition Vacuum Pressure Leak Test

Posted by admin at March 23, 2024

Category: manifold

Tags: air-condition, digital, gauge, leak, manifold, meter, pressure, temperature, test, vacuum

ANCEL AC3000 digital manifold is a professisional instrument for installation, testing and maintenance of refrigeration equipment suchas air conditioners and cold stores. It combines 2-way pressure test, dual temperature measurements (with optionaldual temperature probes), a 32-bit digitalprocessor and a large LCD in one easy-to-useinstrument with the following main functions. Pressure and Saturation Temperature. Pressure Leak Test with recording. Direct T1 T2 Temperature, Real-timeSuperheat and Subcooling Simultaneously Display with Optional Two Clamp-onTemperature Probes. 5.89 Refrigerant Profiles Stored in The Instrument. Automatic Multi-unit Pressure Conversion. Automatic Temperature? /? Conversion. It is the right one you have to do the job right. Turn off the blue valve and red valve. Turn on the instrument. Then verify that LCD displays the status of the pressure test. If not, press the function button to switch it. When the instrument is turned on, theremay be 10 digits in the high and low pressure display area. Press R+/ R- buttons, Unit button and? /? Button to select tested refrigerant and reading display respectively. If the clamp-on temperature probes havebeen connected to the instrument, the real-time temperature will be displayed. If not, no display of it. Connect the instrument to the refrigeration system according to thechart below. Turn on the refrigerant valve and gently press the pressure release valve to vent the air in the connecting hose. When the refrigeration system stops, turnon the high pressure valve (red valve) and fill with a certain amount of refrigerant and then shut the valve quickly. Run the refrigeration system, turn on the low pressure valve (blue valve), and fill with the refrigerant into the refrigeration system. After the filling is completed, shut the low pressure valve (blue valve) and refrigerant valve. Let the refrigeration system running. Shut down the refrigeration system, make sure all valves are turned off, then disconnect the instrument between refrigeration system and source. Do not remove the high pressure valve connection until the pressure drops to the safe point. Then turn off the instrument. The filling operation of different equipment or refrigerants may vary. Please read carefully the relevant specific operation requirements for filling operation, so as to avoid damage to user or equipment caused by improper operation! The instrument can display the corresponding Evaporation Temperature(EV) and Condensation Temperature (CO) during the refrigerant pressure test. If the clamp-on temperature probes are connected to the instrument, LCD will display the real-time temperature in the spot T1 Sensor and T2 Sensor. Please make sure clamp-on temperature probes are connected as step 6 and contacted fully to the refrigeration pipes. The instrument can calculate the SH-Superheat and SC – Subcooling as long as the tested refrigerant ispreset and clamp-on temperature probes are connected well. Power on the instrument. Then make surethe LCD displays vacuum test status. If not, press the Function button to switch it. When the instrument is turned on, there may be 10 digits in the high and low pressure display area. Press the unit button to adjust the reading unit. Connect the instrument to the refrigeration system. Connected clamp-on temperature probes will not affect the operation. Turn on the blue valve and red valve, andstart the vacuum pump. After the vacuum operation is completed, turn off the blue valve and red valve, then shut the vacuum pump. At this time, pressure leak test mode can be used to check leakage in the system (Please refer to Pressure Leak Test). The instrument is powered on with the blue and red valves turned off. Press the Function button to pressure leak test mode. The current pressure value is displayed at lower rightcorner of LCD. Press the Run/Stop button to start the leak test. At this time, the lower left corner records the initial pressure value; the lower right corner displays the instantaneous pressure value; the “P” display area shows the difference between the initial pressure value and the instantaneous pressure value. The time display shows how long the leak test will take, in hour : minute (HH:MM)format. All pressure units on the screen are the same. You can switch between the different pressure units by pressing the Unit button. 89 Kids of Refrigeant Database. Built-in 89 kinds of refrigerant NIST: According to AmericanNIST standard. R11 R113 R114 R115 R116 R12 R123 R124 R125 R1270. R13 R134A R14 R141B R142B R143A R152A R170 R21 R218. R22 R227EA R23 R236EA R245CA R245FA R290 R32 R401A R401B. R401C R402A R402B R403A R403B R404A R405A R406A R407A R407B. R407C R407D R407E R408A R409A R409B R41 R410A R410B R411A. R411B R412A R413A R414A R414B R415A R415B R416A R417A R418A. R419A R420A R421A R421B R422A R422B R422C R422D R423A R424A. R425A R426A R427A R428A R50 R500 R501 R502 R503 R504. R507A R508A R507B R509A R600 R600A R707 R7441C02 R1234. Wide Range of applications. Pressure test: gauge pressure. Pressure test unit: Kpa; Mpa; bar; inHg; PSI. Pressure test range: 0 Kpa – 6000 Kpa. Pressure test resolution: 1 Kpa. Pressure test accuracy: +/- 0.5 %(FS)+ 5dgt. Pressure overload limit: 10000 Kpa (10 Mpa; 100 bar;). Vacuum test: relative vacuum. Vacuum test unit: Kpa; Mpa; bar; inHg; PSI. Vacuum test range: -101 Kpa – 0 Kpa. Vacuum test resolution: 1 Kpa. Temperature test unit: °C (Celsius), °F (Fahrenheit). Temperature test range: -40°C-150°C (-40°F-302°F). 0.1°C (-40°C-99.9°C), 1°C (100°C-150°C). 0.1°F (-40°F-99.9°F), 1°F (100°F-302°F). Temperature test accuracy: +/- 0.5 °C + 2dgt +/- 0.9 °F + 2dgt. Power Supplies: 4 X 1.5V SIZE. AA / LR6 Battery not include. Ancel AC3000 refrgerantion Digital Manifold Gauge. Clamp on temperature probe socket. 5, R+/R-Refrigerant Type Selection Buttons. 10, High Pressure Button. 11, Refrigerant Obezervation Window. 12, Pressure release valve. 13, Refrigerant inlet/vacuum Pump inlet. 14, Low Pressure Valve. 15,1/4 inch high pressure inlet. 1 x AC3000 Manifold Digital Meter. 1 x Paper Box. 1 x User Manual. Clean the exterior with a damp cloth. Do not use harsh solvents. Keep screw connections clean and free of grease, clean with a moist cloth as required. Carefully blow out oil residues in valve block using compressed air. Replace the batteries when low battery power indication lights on in LCD. Low battery power supply. The instruments has low power sign. When it is displayed, it means the battery power is insufficient. At this time, the battery should be replaced as required in order to avoid affecting normal use. Damaged refrigerant hose orvalve stem. Please check the pipe connections and hoses before testing. If you find any damage, please replace them immediately to avoid improper use or accident. Failure of refrigerant filling. There is a valve core in the refrigerant inlet of the refrigeration system. When connecting the instrument, pay attention the two terminals of the hoses. Connect one terminal with a core to the refrigeration system, while another terminal without acore to the instrument. Every hose terminal comes with a nylonpad that is limited a certain life of using. Over use or other situation will make itdefective, which result in leakage. The instrument refrigerant inlet (the middle port of the instrument) has a port with valve core, which is used to vent the air in the hoes after connecting the refrigerant to the instrument. The port is equipped with a copper plug screw. It is required to tighten it every time before or after operation. Check the refrigeration system’s pipes and connectors. Credit cards? Debit card? Apple Pay? Google Pay ect. Carrier and Logistics: All Orders are. Free repair for the devices. OBDII Code Reader, Car Diagnostic Tool, Truck Diagnostic Tool, EVAP Smoke Machine, Car Power Probe, Battery Tester. The price is reasonable and we have top rated after-sales service. Our main brand is. And we also sell other brands product, such as. FOXWELL, LAUNCH, THINKCAR, AUTOPHIX. GMT8 (9:00-18:00). From Monday to Friday.

No Comments

Refrigeration Air Conditioning

Posts Tagged ‘leak’